Stereo 2.1W Class D Audio Amplifier - TPA2012

Stereo 2.1W Class D Audio Amplifier - TPA2012

Stereo 2.1W Class D Audio Amplifier - TPA2012 elevates your projects with amplified sound effects.

$12.95
Tax included
 Backorders Accepted. Ships in 2-3 weeks
 Customer ratings and reviews
Nobody has posted a review yet
in this language
  • Products in stock -  Same day shipping within business hours
Products on backorder - Usually ships in 10-15 working days depending on manufacturer Products in stock - Same day shipping within business hours Products on backorder - Usually ships in 10-15 working days depending on manufacturer
  • Return policy - Any product that is defective or damaged upon arrival can be replaced within 10 days Return policy - Any product that is defective or damaged upon arrival can be replaced within 10 days
PayPal

With proper and audible sound effects one is able to elevate the impact of their electronics project.

This incredibly small stereo amplifier is surprisingly powerful - able to deliver 2 x 2.1W channels into 4 ohm impedance speakers (@ 10% THD). Inside the miniature chip is a class D controller, able to run from 2.7V-5.5VDC. Since the amp is a class D, it's incredibly efficient (89% efficient when driving an 8Ω speaker at 1.5 Watt) - making it perfect for portable and battery-powered projects. It has built in thermal and over-current protection but we could barely tell it got hot. This board is a welcome upgrade to basic "LM386" amps!

The inputs of the amplifier go through 1.0uF capacitors, so they are fully 'differential' - if you don't have differential outputs, simply tie the R- and L- to ground. The outputs are "Bridge Tied" - that means they connect directly to the outputs, no connection to ground. The output is a ~300KHz square wave PWM that is then 'averaged out' by the speaker coil - the high frequencies are not heard. All the above means that you can't connect the output into another amplifier, it should drive the speakers directly.

Comes with a fully assembled and tested breakout board with 1.0uF input capacitors. We also include a dual mini DIP switch for setting the amplifier gain on the fly, 3.5mm screw-terminal blocks so you can easily attach/detach your speakers, and some header in case you want to plug it into a breadboard. You will be ready to rock in 15 minutes! Speakers are not included, use any 4 ohm or 8 ohm impedance speakers.

  • Output Power: 2.1W at 4Ω, 10% THD, 1.4W at 8Ω, 10% THD, with 5V Supply
  • PSRR: 77 dB typ @ 217 Hz with 6 dB gain
  • Designed for use without an output filter, when wires are kept at under 2"-4" long
  • Four pin-selectable gains: 6dB, 12dB, 18dB and 24dB. Select with the onboard switches or by setting the G0 and G1 breakout pins (see schematic for breakout board showing gain pin settings for details)
  • Excellent click-and-pop suppression
  • Thermal shutdown protection
  • Independent channel shutdown
  • Low current draw: typ 6mA quiescent and 1.5uA in shutdown mode

Check out the tutorial for more details!

Technical details

  • Dimensions (without 0.1" header): 22.96mm / 0.9" x 28.33mm / 1.11" x 4.97mm / 0.19"
  • Weight: 2.56g

Revision History: As of May 23, 2016 we've updated this breakout to use the TPA2012 rather than the TS2012. This is an overall-equivalent part with slightly less power output. You can use the two interchangeably for 99% of projects. The TS2012 has been discontinued!

Documents

Datasheets, schematics, PCB files, Fritzing object and more in the tutorial!

AF-1552/01
 Reviews

Be the first to write your review !